Product Description

Spinlock Deckvest 6D 170N PFD with HRS System
Fully featured, lightweight, front opening lifejacket harness with automatic inflation and harness release system.

Features:

• 170N and 275N Buoyancy

• One Size

• UML Pro Sensor Elite activation system

• Improved front opening buckle with smooth body adjuster system

• Enhanced shoulder fit system for the perfect fit – every time – all day

• Enhanced back profile for clean, unobtrusive look and fit

• Hard-wearing coated fabrics in key areas

• New sprayhood design with large clear structured visor – stored away from neck

• Firing system on rear of bladder for improved comfort and reduced snagging when inflated

• 40mm Single Leg Strap with stowage pocket - extra wide, easy to find, easy to locate

• Pylon 360° lifejacket light fitted

• Lume-On bladder illumination lights fitted

• MOB1 AIS Compatible

• 5 Year Warranty on product registration

• Cutter attachment point for non-HRS models

• Harness Release System (HRS)

Approvals:
The Deckvest 6D is approved to the following international standards:
CE Approved:
ISO12402-3 170N Lifejacket
ISO12402-2 275N Lifejacket
ISO12401 Deck Harness

Pylon Light ISO 12402-8
Sprayhood ISO 12402-8
Requires 1 x 33g CO2 cylinder

Harness Release System:

Spinlock's Deckvest VITO and Deckvest 6D both have the option of a Harness Release System (HRS), a soft loop attachment point for a safety line which can be released in an emergency to free a person from their safety line.
• Activation handle located behind soft loop, easy to locate, grab and pull
• Soft loop attachment released and open
• User separated from safety line and boat
• Easily reset to use again
• ISO12402-1 Deck Safety Harness
The Spinlock Harness Release System (HRS) is a new innovation which enables the wearer to disconnect from the safety line by releasing a lever behind the soft loop safety line attachment point of the lifejacket harness.
What is HRS?
Spinlock still considers a knife to be an essential piece of carried equipment. However, we have yet to develop a reliable consistent safety line clip release system. Instead, we are focused on developing a release system of the actual lifejacket harness. Testing showed that the harness release system needed to be simple to understand, simple to use and simple to maintain as well as reliable over the lifetime of the lifejacket. At the same time, the harness release system must meet the requirements of the ISO12402 approval.
Staying connected to the boat is undoubtedly safer than being in the water and use of a safety line is actively encouraged. However, in the event of a fall overboard, a casualty can find themselves being dragged/trapped alongside or behind the vessel. A situation which can be hard to be released from.

Read more about the .

If required – at an additional cost, Spinlock can upgrade any Deckvest 6D to include the new Harness Release System.

Inflation System:

UML Pro Sensor ELITE inflator
The Pro Sensor Elite® Automatic Inflator replaces the Pro Sensor® Automatic Inflator late in 2018 (13mm shorter and 4 grams lighter than the original Pro Sensor® Automatic Inflator).
This is a water sensitive activation system, that uses a compressed paper capsule which dissolves when wet, which then releases a spring to puncture the CO2 cylinder.
The cap is designed so that only water flowing upwards through the unit will cause it to activate. Water, spray and rain running down the jacket will not cause activation.
The Pro Sensor ELITE has two indicators that show the status of the CO2 cylinder and firing head.

For Hammar® inflation see

See

Through Life Support:

Lifejacket warranty is extended to 5 years upon registration*

Registering your Deckvest gives you the benefit of our unique online support, to help ensure that your lifejacket is reliably maintained.

• Prompts for winter care, storage and pre-season safety checks
• Access to latest online support and advice
• Updates on MOB prevention and advice

Size Guide: